全國服務熱線
13503801616
全國服務熱線
13503801616
新聞資訊
News
嘉興市力矩電機廠家 力矩電機700圖片
嘉興市力矩電機廠家 力矩電機700圖片
新鄉市力矩電機生產基地-河南恒通電機力矩電動機全、高清圖片。為您機械設備配套佳選。該力矩電機軟特性恒定。工作狀態發熱退磁低。電機經久耐用，絕緣等級高于同行業。力矩安裝前的準備
Third, pre-installation preparation
1.力矩電動機使用前應該檢查電動機外表是否完善無損傷，有無受潮的現象。
1. The motor should be checked before using， there has to be no damage on the motor outside, and the motor can not be damped.
2.檢查電動機的銘牌數據是否符合要求。
2. Check the motor nameplate data to meet the requirements.
3.仔細檢查電動機在運輸過程中有無變形或者損壞，緊固件有無松動或者脫落，試著用手撥動轉軸，看電動機是否能靈活運轉。
電動機的安裝
3. Carefully check motor during transport without deformation or damage, fasteners loose or fall off, try to toggle the shaft by hand to see if the motor can operate flexibly.
4．力矩電動機應該按照其結構形式正確安裝，電動機的軸伸直徑出廠前已精磨至標準公差尺寸，因此要求用戶所配套的皮帶輪或者其他配套零件的內徑尺寸一定要按照國家標準推薦的優先配合公差進行磨削或者鉸削加工。安裝時，用手推入或用榔頭輕敲至軸伸臺即可，嚴禁用錘猛擊，否則將損壞電動機的零件，造成電動機不能正常工作。
4.You must assemble the electric motor according to the instruction types. The shaft’s diameter of the motor
must be grinded according to the standard size of allowable drror. So the customers will grind or cut processing
according to the national standard difference with complete leather belts or else parts. When you assemble
it, you may push the shaft lightly not use the hammer to hit it or you will demage the parts.
5．為確保設備和人身安全，在電動機通電前，請務必把接地導線連接到電動機的接地螺釘上，并正確接地。接地導線應采用銅導線，其截面積隨電動機功率的增加而加大。小功率電動機接地線的截面積應不小于1平方毫米。
5.In order to ensure the person’s safe, you must connect the earth conductor to the landing screw. The landing
wire should be copper. Its cross area is being increased as the electric motor’s power is adding. The across
area of little power motors should be not less than 1 square mm.
6．力矩電動機的安裝應保證良好的通風冷卻條件，不可用于熱曬雨淋的場所。
6.Install the motor should ensure good ventilation and cooling conditions, it can not be used for places with
sun exposure or in rain.
返回頂部
